[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [microblaze-uclinux] Re: memec uclinux




Roberto,
I have been trying to get the uClinux running with the auto-config and a month ago you said you where working with the autoconfig on the memec v2p7 board.  I was wondering if you have had any success yet?  I have been struggling with it to get it working but with no luck.  Also I tried the document on your site listed below and when I ran the make commands it crashes out and can nto find certain files it seems to need.  Any chance if you have had no luck with the auto-conifg that you might have an old edk project and image file that I can try running on my board with out the p160 module?
Thanks
Brett



Roberto Farina <roberto.farina@cefriel.it>
Sent by: owner-microblaze-uclinux@itee.uq.edu.au

03/04/2005 04:27 AM

Please respond to
microblaze-uclinux@itee.uq.edu.au

To
mcnernbm@notes.udayton.edu
cc
microblaze-uclinux@itee.uq.edu.au
Subject
[microblaze-uclinux] Re: memec uclinux





-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

No problems. when i'll make all the things running fine (and i'll hope
it will be asap ;) ) I''l post to the ml.

I'll also make everything available for dwld in the susal place

www.cefriel.it/delta

you need to register but it'sd for free; it's just a way to control the
activity of our site

There's no need of the P160 module to run uClinux: our first prj and
port were made without it. Of course, P160 brings eth and flash so you
can deal with a more complete but complex system.

Best regards
Roberto

mcnernbm@notes.udayton.edu wrote:
|
| Roberto,
| That sounde excellent.  Do you think once you have that up you could
| email me a copy of the edk project?  Also if you need any help with
| anything on it let me know.  I am still learning the uclinux stuff but
| have gotten fairly good with the edk software.  I would be more then
| willing to help in anyways possible.  Cause getting uclinux on the memve
| v2p7 would be a huge help for are research project.  Also is it required
| to have the p160 module with the ethnet and extra serial port or the
| system ace module to run the uclinux?  Just want to verify I have all
| the hardware I need otherwise I will go and order what is needed.
| Thanks again for all the help
| Brett

- --
Roberto Farina
CEFRIEL ­ Politecnico di Milano
Via Fucini, 2 · 20133 Milano (Italy)
p. +39 02 23954 345 - f. +39 02 23954 254
e. roberto.farina@cefriel.it - w. www.cefriel.it
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.7 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org

iD8DBQFCKCnmzF5ONZxALKMRAjnqAJsF3W9DXSS9mVBBA+JaxKQ5kQ64rwCeL7N8
4EcItHsTkEBECP5J8YEvtww=
=zzgp
-----END PGP SIGNATURE-----
___________________________
microblaze-uclinux mailing list
microblaze-uclinux@itee.uq.edu.au
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/