[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [microblaze-uclinux] Re: memec uclinux
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Can you pls post your msg error?
Are u using the same kernel version / hw configuration / sw configurations?
I'll post the prj as soon as I can; I'm also considering to put it on
the Delta web site
Best regards
Roberto
mcnernbm@notes.udayton.edu wrote:
>
> Roberto,
> At least I am not the only one expereincing this problem. Do you by any
> chance have any of your old projects that you did get to boot prior to
> the auto-config? I tird following your document and it will not build
> it keeps giving me (/include) could nto be found or something alot those
> lines. I wil try it again today but have had little luck in getting
> anything at all to build or boot on the memec v2p7 board.
> Thanks
> Brett
>
>
>
> *Roberto Farina <roberto.farina@cefriel.it>*
> Sent by: owner-microblaze-uclinux@itee.uq.edu.au
>
> 04/19/2005 05:37 AM
> Please respond to
> microblaze-uclinux@itee.uq.edu.au
>
>
>
> To
> microblaze-uclinux@itee.uq.edu.au
> cc
>
> Subject
> Re: [microblaze-uclinux] Re: memec uclinux
>
>
>
>
>
>
>
>
> Unfortunately I didn't succeeded in make the auto-config running. In
> addition, at the present I have little time to further investigate the
> problem.
>
> All I can say is that I never experienced the timing problems John was
> talking about when he posted his prj. I'0ve also to say that in one of
> my last tests I reached your exact point and init reported some problem :(
>
> Let me go and find my prj; I'll send on the ML hoping somebody got the
> time to improve it ..
>
> Best regards
> Roberto
>
>
> mcnernbm@notes.udayton.edu wrote:
>>>
>>> Roberto,
>>> I have been trying to get the uClinux running with the auto-config and a
>>> month ago you said you where working with the autoconfig on the memec
>>> v2p7 board. I was wondering if you have had any success yet? I have
>>> been struggling with it to get it working but with no luck. Also I
>>> tried the document on your site listed below and when I ran the make
>>> commands it crashes out and can nto find certain files it seems to need.
>>> Any chance if you have had no luck with the auto-conifg that you might
>>> have an old edk project and image file that I can try running on my
>>> board with out the p160 module?
>>> Thanks
>>> Brett
>>>
>>>
>>>
>>> *Roberto Farina <roberto.farina@cefriel.it>*
>>> Sent by: owner-microblaze-uclinux@itee.uq.edu.au
>>>
>>> 03/04/2005 04:27 AM
>>> Please respond to
>>> microblaze-uclinux@itee.uq.edu.au
>>>
>>>
>>>
>>> To
>>> mcnernbm@notes.udayton.edu
>>> cc
>>> microblaze-uclinux@itee.uq.edu.au
>>> Subject
>>> [microblaze-uclinux] Re: memec uclinux
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>> No problems. when i'll make all the things running fine (and i'll hope
>>> it will be asap ;) ) I''l post to the ml.
>>>
>>> I'll also make everything available for dwld in the susal place
>>>
>>> www.cefriel.it/delta
>>>
>>> you need to register but it'sd for free; it's just a way to control the
>>> activity of our site
>>>
>>> There's no need of the P160 module to run uClinux: our first prj and
>>> port were made without it. Of course, P160 brings eth and flash so you
>>> can deal with a more complete but complex system.
>>>
>>> Best regards
>>> Roberto
>>>
>>> mcnernbm@notes.udayton.edu wrote:
>>> |
>>> | Roberto,
>>> | That sounde excellent. Do you think once you have that up you could
>>> | email me a copy of the edk project? Also if you need any help with
>>> | anything on it let me know. I am still learning the uclinux stuff but
>>> | have gotten fairly good with the edk software. I would be more then
>>> | willing to help in anyways possible. Cause getting uclinux on the memve
>>> | v2p7 would be a huge help for are research project. Also is it required
>>> | to have the p160 module with the ethnet and extra serial port or the
>>> | system ace module to run the uclinux? Just want to verify I have all
>>> | the hardware I need otherwise I will go and order what is needed.
>>> | Thanks again for all the help
>>> | Brett
>>>
> ___________________________
> microblaze-uclinux mailing list
> microblaze-uclinux@itee.uq.edu.au
> Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
> Mailing List Archive :
> http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/
>
> --
> Roberto Farina
> CEFRIEL Politecnico di Milano
> Via Fucini, 2 · 20133 Milano (Italy)
> p. +39 02 23954 345 - f. +39 02 23954 254
> e. roberto.farina@cefriel.it - w. www.cefriel.it
___________________________
microblaze-uclinux mailing list
microblaze-uclinux@itee.uq.edu.au
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive :
http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/
- --
Roberto Farina
CEFRIEL Politecnico di Milano
Via Fucini, 2 · 20133 Milano (Italy)
p. +39 02 23954 345 - f. +39 02 23954 254
e. roberto.farina@cefriel.it - w. www.cefriel.it
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.7 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org
iD8DBQFCZf31zF5ONZxALKMRAh4gAJwLbe/7zOlA8YgkNKjEDYNWFR4WPgCgy4Cd
mBV5amEK2mQiMZdvz1isnGU=
=2KVZ
-----END PGP SIGNATURE-----
___________________________
microblaze-uclinux mailing list
microblaze-uclinux@itee.uq.edu.au
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/