[microblaze-uclinux] DL Errors

["Abot Botbot" <dejanigma@xxxxxxxxxxx>]

Folks,

   In an attempt to circumnavigate my problem, I brought my system.bit over 
to my windows machine and programmed the hardware just fine.  Then I flipped 
back to the linux box and tried to do #./dl.sh and I get the following 
output:

[root@ANDYD_LINUX project1]# ./dl.sh
Memory address Found
Memory Address is 0x24000000
Kimage is /tftpboot/image.bin
Kparams are
Xilinx Microprocessor Debug (XMD) Engine
Xilinx EDK 7.1.2 Build EDK_H.12.5.1
Copyright (c) 1995-2005 Xilinx, Inc.  All rights reserved.

XMD%
Loading MHS File..
WARNING:Portability:111 - Message file "EDK.msg" wasn't found.
Processor(s) in System ::

Microblaze(1) : microblaze_0
Address Map for Processor microblaze_0
 (0x00000000-0x00001fff) dlmb_cntlr    dlmb
 (0x00000000-0x00001fff) ilmb_cntlr    ilmb
 (0x22000000-0x227fffff) FLASH_2Mx32   mb_opb
 (0x24000000-0x27ffffff) DDR_SDRAM_64Mx32      mb_opb
 (0x40600000-0x4060ffff) RS232_Uart    mb_opb
 (0x41200000-0x4120ffff) opb_intc_0    mb_opb
 (0x41400000-0x4140ffff) debug_module  mb_opb
 (0x41c00000-0x41c0ffff) opb_timer_1   mb_opb

Reusing 78023D61 key.
Connecting to cable (Parallel Port - parport0).
WinDriver v6.03 Jungo (c) 1997 - 2003 Build Date: Aug 10 2003 X86 15:27:16.
parport0: baseAddress=0x378, ecpAddress=0x778
LPT base address = 0378h.
ECP base address = 0778h.
ECP fifo status bits not initialized properly.
Unable to detect the ECP hardware. The hardware may be malfunctioning or the
BIOS setting for the Parallel port is not set to ECP mode.
Cable connection established.

JTAG chain configuration
--------------------------------------------------
Device   ID Code        IR Length    Part Name
1       0a001093           8        System_ACE
2       05059093          16        XCF32P
3       0167c093          10        XC4VLX25
4       09608093           8        xc95144xl
Assuming, Device No: 3 contains the MicroBlaze system
Connected to the JTAG MicroProcessor Debug Module (MDM)
No of processors = 1

MicroBlaze Processor 1 Configuration :
-------------------------------------
Version............................2.10.a
No of PC Breakpoints...............1
No of Read Addr/Data Watchpoints...0
No of Write Addr/Data Watchpoints..0
Instruction Cache Support..........off
Data Cache Support.................off
JTAG MDM Connected to MicroBlaze 1
Connected to "mb" target. id = 0
Starting GDB server for "mb" target (id = 0) at TCP port no 1234
Setting current target to target id 0
List of connected targets

Target ID          Target Type
------------------------------
0                  MicroBlaze MDM-based (hw) Target *
XMD% INFO:MDT - MHS File already loaded
XMD%
Processor (1) Already Connected

XMD% Downloading kernel image...
XMD% This will only take a few seconds!
XMD% XMD% setting kernel command line
XMD%
XMD% cmdline is
XMD% 2
XMD% 0x100
XMD% > > > > XMD% XMD% XMD% XMD% Processor started. Type "stop" to stop 
processor
RUNNING> Done already WOW!
RUNNING> Closing MDM communication with Processor 1
[root@ANDYD_LINUX project1]#


I dont see anthing on hyperterminal or minicom, and I'm pretty sure i got it 
set up correctly. The error light comes on on my ML401 board, so it doesnt 
look like programming the image worked perfectly. Any ideas?

Thanks,
Andy

_________________________________________________________________
FREE pop-up blocking with the new MSN Toolbar ? get it now! 
http://toolbar.msn.click-url.com/go/onm00200415ave/direct/01/

___________________________
microblaze-uclinux mailing list
microblaze-uclinux@xxxxxxxxxxxxxx
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/