[microblaze-uclinux] Problem with Ethernet: I can't ping

["Qichen Huang" <huangqichen@xxxxxxxx>]

Hi everyone,

I've followed the instructions from John Williams and Jason Wu, and
finally got uClinux-kernel booted on my Spartan-3E-Starter-Kit
( http://www.xilinx.com/xlnx/xebiz/designResources/ip_product_details.j...).

However, there's no boot message on the terminal, I got just a login
prompt when the kernel started:
uclinux-auto login:

Anyway, the kernel still works.
Then I tried to test the networking and followed the instructions.

There's no problem to ping itself. But I can't ping my PC, which is
connected to the Eva-Board using crossover cable. There's even no ARP
packets received.
It seems that the RX- and TX-pins are not connected to the FPGA. Did I
miss something?

Any help is appreciated.

Qichen

PS:
The auto-config.in is generated by EDK Libgen (8.1 sp2) and directly
copied to
uClinux-dist/linux-2.4.x/arch/microblaze/platform/uclinux-auto/

The eth0 settings are as follows:
# ifconfig eth0
eth0     Link encap:Ethernet  HWaddr 00:00:C0:A3:E5:44
           inet addr:192.168.1.4  Bcast:192.168.1.255
Mask: 255.255.255.0
           UP BROADCAST RUNNING MTU:1500  Metric:1
           RX packeckts:0 errors:0 dropped:0 overruns:0 frame:0
           TX packeckts:54 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
                         Interrupt:2

The section of opb_ethernet in the system.mhs is as follows:

BEGIN opb_ethernet 
  PARAMETER INSTANCE = Ethernet_MAC 
  PARAMETER HW_VER = 1.04.a 
  PARAMETER C_DMA_PRESENT = 1 
  PARAMETER C_IPIF_RDFIFO_DEPTH = 32768 
  PARAMETER C_IPIF_WRFIFO_DEPTH = 32768 
  PARAMETER C_OPB_CLK_PERIOD_PS = 20000 
  PARAMETER C_BASEADDR = 0x40c00000 
  PARAMETER C_HIGHADDR = 0x40c0ffff 
  BUS_INTERFACE SOPB = mb_opb 
  PORT OPB_Clk = sys_clk_s 
  PORT PHY_tx_clk = fpga_0_Ethernet_MAC_PHY_tx_clk 
  PORT PHY_rx_clk = fpga_0_Ethernet_MAC_PHY_rx_clk 
  PORT PHY_crs = fpga_0_Ethernet_MAC_PHY_crs 
  PORT PHY_dv = fpga_0_Ethernet_MAC_PHY_dv 
  PORT PHY_rx_data = fpga_0_Ethernet_MAC_PHY_rx_data 
  PORT PHY_col = fpga_0_Ethernet_MAC_PHY_col 
  PORT PHY_rx_er = fpga_0_Ethernet_MAC_PHY_rx_er 
  PORT PHY_tx_en = fpga_0_Ethernet_MAC_PHY_tx_en 
  PORT PHY_tx_data = fpga_0_Ethernet_MAC_PHY_tx_data 
  PORT PHY_Mii_clk = fpga_0_Ethernet_MAC_PHY_Mii_clk 
  PORT PHY_Mii_data = fpga_0_Ethernet_MAC_PHY_Mii_data 
  PORT IP2INTC_Irpt = Ethernet_MAC_IP2INTC_Irpt 
 END