I want to download my linux image to Xilinx ML403 board using the download script provided in the Microblaze-Tutorial from John Williams.
No target with id: -1. Use command "targets" to get
target list
Error: Invalid xmd target:
-1
Use "targets" command to get current list
of targets or change target
Use "connect mb"
command to connect to a MicroBlaze target
Use
"connect ppc" command to connect to a PowerPC target
I didn't find anything about the invalid target-id,
and I did not find any
Correspondig -1 in the
download script.
Any ideas?
I did not update opb_mdm to Version 2.01a since i have XCFX12-FF668-10 (not V4LX25 ES)
Philipp
$ ./dl.sh
Kimage
is binaries/image.bin
Kparams are
Xilinx Microprocessor Debug (XMD) Engine
Xilinx EDK 8.2 Build EDK_Im.14
Copyright (c) 1995-2005 Xilinx, Inc. All rights
reserved.
XMD%
XMD% Loading
MHS File..
Processor(s) in System ::
Microblaze(1) : microblaze_0
Address Map for Processor microblaze_0
(0x00000000-0x00001fff) dlmb_cntlr
dlmb
(0x00000000-0x00001fff)
ilmb_cntlr ilmb
(0x28000000-0x2bffffff) DDR_SDRAM_64Mx32
mb_opb
(0x2c000000-0x2c7fffff)
FLASH_2Mx32 mb_opb
(0x40600000-0x4060ffff) RS232_Uart mb_opb
(0x41200000-0x4120ffff) opb_intc_0
mb_opb
(0x41400000-0x4140ffff)
debug_module mb_opb
(0x41c00000-0x41c0ffff) opb_timer_1 mb_opb
XMD% Connecting to cable (Parallel Port -
LPT1).
Checking cable driver.
Driver windrvr6.sys version = 7.0.0.0. LPT
base address = 0378h.
ECP base address
= 0778h.
Cable connection failed.
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 7.0.0.0. LPT base address =
0378h.
ECP base address = 0778h.
Cable connection failed.
Connecting to cable (Parallel Port - LPT2).
Checking cable driver.
Driver
windrvr6.sys version = 7.0.0.0.Cable connection failed.
Connecting to cable (Parallel Port - LPT2).
Checking cable driver.
Driver windrvr6.sys version = 7.0.0.0.Cable connection
failed.
Connecting to cable (Usb Port -
USB22).
Checking cable driver.
Driver xusbdfwu.sys version: 1021
(1021).
Driver windrvr6.sys version =
7.0.0.0.Calling setinterface num=0, alternate=0.
DeviceAttach: received and accepted attach for:
vendor id 0x3fd, product id 0x8, device handle
0x2930038
Cable PID = 0008.
Max current requested during enumeration is
280 mA.
Cable Type = 3, Revision =
0.
Setting cable speed to 6 MHz.
Cable connection established.
Firmware version = 1021.
CPLD file version = 0012h.
CPLD
version = 0012h.
JTAG chain configuration
--------------------------------------------------
Device ID
Code IR Length Part
Name
1
0a001093
8 System_ACE
2
05059093
16 XCF32P
3
01e58093
10 XC4VFX12
4
09608093
8 xc95144xl
Assuming, Device No: 3 contains the MicroBlaze system
WARNING:MDT - MDM Peripheral Not Detected on
Hardware
WARNING:MDT - Assuming opb_jtag_uart
peripheral
Connected to the JTAG
MicroProcessor Debug Module (MDM)
No of
processors = 1
UNKNOWN Processor Version (0)
Verify if FPGA
Bitstream was downloaded and DONE pin went High
XMD% Downloading kernel image...
XMD% This will only take a few seconds!
XMD%
No target with id: -1.
Use command "targets" to get target list
Error: Invalid xmd target: -1
Use
"targets" command to get current list of targets or change target
Use "connect mb" command to connect to a MicroBlaze
target
Use "connect ppc" command to connect
to a PowerPC target
XMD% XMD% setting kernel
command line
XMD% XMD% "cmdline is "
XMD% 2
XMD%
0x100
XMD% > > > > XMD%
No target with id: -1. Use command "targets" to get
target list
Error: Invalid xmd target:
-1
Use "targets" command to get current list
of targets or change target
Use "connect mb"
command to connect to a MicroBlaze target
Use
"connect ppc" command to connect to a PowerPC target
XMD%
No target with id: -1. Use
command "targets" to get target list
Error:
Invalid xmd target: -1
Use "targets" command
to get current list of targets or change target
Use "connect mb" command to connect to a MicroBlaze target
Use "connect ppc" command to connect to a PowerPC
target
XMD%
No target with id: -1. Use command "targets" to get target list
Error: Invalid xmd target: -1
Use "targets" command to get current list of targets or change
target
Use "connect mb" command to connect to
a MicroBlaze target
Use "connect ppc" command
to connect to a PowerPC target
XMD%
No target with id: -1. Use command "targets" to get
target list
Error: Invalid xmd target:
-1
Use "targets" command to get current list
of targets or change target
Use "connect mb"
command to connect to a MicroBlaze target
Use
"connect ppc" command to connect to a PowerPC target
XMD% Done already WOW!
XMD%