[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [microblaze-uclinux] Porting Petalinux 0.20 Build -rc1 050607 to Digilent's XUPV2P board.
Hi,
Aws Ismail wrote:
> Hi everyone.
>
> I have been trying to migrate Petalinux to digilent's XUPV2P board (Rev.
> 04). I have been following Andrew's howto found here:
>
> http://www.labbookpages.co.uk/fpgas/linux/xupv2proMBLinux.html
>
> But when it comes to booting all I am getting is this (taken from my
> minicom terminal window):
>
> *#### klimit 901c9000 ####
> Moving 0x000f7000 bytes from 0x901b108c to 0x901c8868
> New klimit: 0x902c0000
> L
> *
> And then the booting stops forever as if nothing is happening. Does
> anyone have an idea what's going on? I go through all the steps fine,
> until booting.
I have been working with XUPV2P board. I haven't seen problem in it.
If you can please use latest PetaLinux (it is easier for us to help you).
Please check that your Kconfig.auto correspond with your HW design.
(Be sure that bitstream which you have in FPGA is that one which you want to use - for
example you loading bitstream via JTAG and you have setup Sysace configuration - after
board reset you will use sysace bitstream).
Read linux log buffer
http://www.monstr.eu/wiki/doku.php?id=fdt:fdt#error_logs
If you use latest PetaLinux you can use one script petalinux-send-configs to send your setting.
Regards,
Michal
>
> Regards.
>
> Aws\
>
>
> On Wed, Apr 29, 2009 at 6:54 PM, Andy Greensted <ajg112@xxxxxxxxxxxxxx
> <mailto:ajg112@xxxxxxxxxxxxxx>> wrote:
>
> I put this howto together a few days ago.
> Hope it helps
> http://www.labbookpages.co.uk/fpgas/linux/xupv2proMBLinux.html
>
> Andy
>
> Aws Ismail wrote:
>
> Thanks David for your reply. I am about to start porting it too
> so it's good to share the experience with anyone doing the same
> thing. I do have the SDRAM as a 256 MB DIMM on the board. What
> is your XUPV2P board revision?
>
> Aws\
>
> On Tue, Apr 28, 2009 at 9:25 PM, David Babich
> <dbabich@xxxxxxxxxxxxxxxx <mailto:dbabich@xxxxxxxxxxxxxxxx>
> <mailto:dbabich@xxxxxxxxxxxxxxxx
> <mailto:dbabich@xxxxxxxxxxxxxxxx>>> wrote:
>
> I actually just started working on a port for the Digilent XUPV2P
> board yesterday. I'm doing it in my spare time, so my
> progress may
> be slow. If I run into any issues I'll post as I go along.
> Based
> on passed experience with Petalinux, it is certainly feasible and
> the XUPV2P is more than sufficient to support it provided you
> include the XUPV2P's SDRAM module in your design.
>
>
> ------------------------------------------------------------------------
> *From:* Aws Ismail (SFU) [mailto:aii@xxxxxx
> <mailto:aii@xxxxxx> <mailto:aii@xxxxxx <mailto:aii@xxxxxx>>]
>
> *To:* microblaze-uclinux@xxxxxxxxxxxxxx
> <mailto:microblaze-uclinux@xxxxxxxxxxxxxx>
> <mailto:microblaze-uclinux@xxxxxxxxxxxxxx
> <mailto:microblaze-uclinux@xxxxxxxxxxxxxx>>
>
> *Sent:* Tue, 28 Apr 2009 19:15:05 -0600
> *Subject:* [microblaze-uclinux] Porting Petalinux 0.20 Build
> -rc1 050607 to Digilent's XUPV2P board.
>
>
> Hello Everyone,
>
> I was wondering if anyone have tried porting Petalinux 0.20
> Build rc1 to a Digilent XUPV2P board. If so, where there any
> problems or hurdles encountered. If not, is it even feasible?
>
> I appreciate your input.
>
> -- Aws Ismail, BASc. EE
>
> MASc. Candidate
> Mechatronic Systems Engineering
> Simon Fraser University
> 250-13450 102 Avenue
> Surrey BC V3T 0A3
> ---------
>
>
>
>
> --
> Aws Ismail, BASc. EE
>
> MASc. Candidate
> Mechatronic Systems Engineering
> Simon Fraser University
> 250-13450 102 Avenue
> Surrey BC V3T 0A3
>
> Tel (Cell): 778-889-0526
> ---------
>
>
> --
> Dr. Andrew Greensted Department of Electronics
> Bio-Inspired Engineering University of York, YO10 5DD, UK
>
> Tel: +44(0)1904 432828 Mailto: ajg112@xxxxxxxxxxxxxx
> <mailto:ajg112@xxxxxxxxxxxxxx>
> Fax: +44(0)1904 432335 Web: http://www.labbookpages.co.uk
>
> 2009 IEEE Congress on Evolutionary Computation: http://www.cec-2009.org
> ___________________________
> microblaze-uclinux mailing list
>
> microblaze-uclinux@xxxxxxxxxxxxxx
> <mailto:microblaze-uclinux@xxxxxxxxxxxxxx>
> Project Home Page :
> http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
> <http://www.itee.uq.edu.au/%7Ejwilliams/mblaze-uclinux>
> Mailing List Archive :
> http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/
> <http://www.itee.uq.edu.au/%7Elistarch/microblaze-uclinux/>
>
>
>
>
> --
> Aws Ismail, BASc. EE
>
> MASc. Candidate
> Mechatronic Systems Engineering
> Simon Fraser University
> 250-13450 102 Avenue
> Surrey BC V3T 0A3
>
> Tel (Cell): 778-889-0526
> ---------
--
Michal Simek, Ing. (M.Eng)
PetaLogix - Linux Solutions for a Reconfigurable World
w: www.petalogix.com p: +61-7-30090663,+42-0-721842854 f: +61-7-30090663
___________________________
microblaze-uclinux mailing list
microblaze-uclinux@xxxxxxxxxxxxxx
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/