[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[microblaze-uclinux] system booting problem
Hi,
I am trying to boot the petalinux-dist on a Spartan3E-RevC starter kit. not being able to use the DTE port ,I created my own EDK project with same features except that I use the DCE port.
For u-boot, since I am not using tftp but serial connection for downloads, I downloaded to the Flash with the u-boot "loadb" command the following files:
u-boot-s.bin at address 0x85000000 (sector 0 of Flash)
ub.config.img 0x85020000 (sector 1)
image.ub 0x85080000 (sector 5)
(I choosed these adresses by lookin to the result of the "printenv")
after the downloads, I reset the board.
the booting of the system started but stopped before the uclinux login prompt. Can anyone help me find what step went wrong?
Here is the log:
-----------------------------------------------------------------------------
=================================================
FS-BOOT First Stage Bootloader (c) 2006 PetaLogix
Project name: DCE_Test
Build date: Jul 20 2009 09:58:46 FS
Serial console: Uartlite
=================================================
FS-BOOT: System initialisation completed.
FS-BOOT: Booting from FLASH. Press 's' for image download.
FS-BOOT: Booting image...
SDRAM :
Enabling caches :
Icache:OK
Dcache:OK
U-Boot Start:0x87fc0000
Malloc Start:0x87f80000
Board Info Start:0x87f7ffd0
Boot Parameters Start:0x87f6ffd0
FLASH: 16 MB
ETHERNET: MAC:00:0a:35:00:22:01
*** Warning - bad CRC, using default environment
Hit any key to stop autoboot: 0
## Booting image at 85080000 ...
Image Name: PetaLinux Kernel 2.6
Image Type: Microblaze Linux Kernel Image (uncompressed)
Data Size: 2760848 Bytes = 2.6 MB
Load Address: 86000000
Entry Point: 86000000
Verifying Checksum ... OK
OK
Found romfs @ 0x861b308c (0x000ef000)
#### klimit 861cb000 ####
Moving 0x000ef000 bytes from 0x861b308c to 0x861ca880
New klimit: 0x862ba000
Linux version 2.6.20-uc0 (faiza@desktop) (gcc version 3.4.1 ( PetaLinux 0.20 Build -rc1 050607 )) #4 Mon Jul 20 10:13:57 CEST 2009
setup_cpuinfo: initialising
setup_cpuinfo: No PVR support in CPU. Using static compile-time info
set_cpuinfo_static: Using static CPU info.
setup_memory: max_mapnr: 0x87fff
setup_memory: min_low_pfn: 0x86000
setup_memory: max_low_pfn: 0x2000
On node 0 totalpages: 8192
DMA zone: 64 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 8128 pages, LIFO batch:0
Normal zone: 0 pages used for memmap
Built 1 zonelists. Total pages: 8128
Kernel command line: mtdparts=physmap-flash.0:256K(boot),128K(bootenv),128K(config),4M(image),11M(spare) macaddr=00:0a:35:00:22:01 console=ttyUL0,115200
OPB INTC #0 at 0x81800000
PID hash table entries: 128 (order: 7, 512 bytes)
TIMER at 0x83C00000
disabling early console
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29688k/32768k available
Calibrating delay loop... 49.45 BogoMIPS (lpj=247296)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
xgpio0 #0 at 0x81420000 mapped to 0x81420000 device: 10,185 using IRQ#3
xgpio1 #1 at 0x81400000 mapped to 0x81400000 device: 10,186 using IRQ#2
uartlite.0: ttyUL0 at MMIO 0x84000000 (irq = 4) is a uartlite
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
eth0: using fifo mode.
eth0: No PHY detected. Assuming a PHY at address 0.
eth0: Xilinx EMACLite #0 at 0x81000000 mapped to 0x81000000, irq=1
physmap platform flash device: 01000000 at 85000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x20000,blocks=128
5 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 5 MTD partitions on "physmap-flash.0":
0x00000000-0x00040000 : "boot"
0x00040000-0x00060000 : "bootenv"
0x00060000-0x00080000 : "config"
0x00080000-0x00480000 : "image"
0x00480000-0x00f80000 : "spare"
uclinux[mtd]: RAM probe address=0x861ca880 size=0xef000
Creating 1 MTD partitions on "RAM":
0x00000000-0x000ef000 : "ROMfs"
uclinux[mtd]: set ROMfs to be root filesystem index=5
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 84k freed
-------------------------------------------------------------------
___________________________
microblaze-uclinux mailing list
microblaze-uclinux@xxxxxxxxxxxxxx
Project Home Page : http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux
Mailing List Archive : http://www.itee.uq.edu.au/~listarch/microblaze-uclinux/